What are the operating procedures of a mortar injection pump?

Aug 18, 2025

Leave a message

As a supplier of mortar injection pumps, I am well - versed in the operating procedures of these essential machines. Mortar injection pumps are widely used in construction projects for tasks such as filling voids, grouting, and injecting mortar into various structures. In this blog, I will guide you through the step - by - step operating procedures of a mortar injection pump.

Pre - operation Checks

Before starting the mortar injection pump, a series of pre - operation checks are crucial to ensure safe and efficient operation.

1. Machine Inspection

First, visually inspect the entire mortar injection pump. Check for any signs of physical damage, such as cracks in the pump body, loose bolts, or damaged hoses. Ensure that all the components are properly assembled and in good condition. For instance, examine the hopper to make sure it is clean and free from any debris that could clog the pump.

2. Lubrication

Proper lubrication is essential for the smooth operation of the pump. Check the oil levels in the gearbox, bearings, and other moving parts according to the manufacturer's specifications. If the oil levels are low, refill them with the recommended lubricant. This helps to reduce friction and wear, extending the lifespan of the pump.

3. Electrical and Hydraulic Systems

If your Mortar Injection Pump is electrically powered, inspect the electrical connections. Make sure all the wires are properly connected, and there are no signs of fraying or damage. For hydraulic pumps, check the hydraulic fluid level and the condition of the hydraulic hoses. Any leaks in the hydraulic system should be repaired immediately to avoid loss of pressure and potential damage to the pump.

4. Material Preparation

Prepare the mortar mixture according to the project requirements. The consistency of the mortar is critical; it should be neither too thick nor too thin. A well - mixed mortar ensures smooth pumping and proper filling. Use a high - quality mixer to blend the cement, sand, water, and any additives thoroughly.

Starting the Pump

Once all the pre - operation checks are completed, you can start the mortar injection pump.

1. Prime the Pump

Priming is an important step to remove air from the pump and the hoses. Fill the hopper with a small amount of water or a thin mortar mixture. Start the pump and let the water or mixture circulate through the system until all the air is expelled. This helps to prevent air locks, which can cause the pump to lose pressure and stop working.

2. Set the Pump Parameters

Adjust the pump parameters such as flow rate and pressure according to the requirements of the project. Different applications may require different flow rates and pressures. For example, when injecting mortar into small voids, a lower flow rate and higher pressure may be needed, while for large - scale grouting, a higher flow rate may be more appropriate. Refer to the pump's user manual for detailed instructions on how to set these parameters.

3. Start the Pumping Process

After priming and setting the parameters, start the main pumping process. Slowly introduce the prepared mortar mixture into the hopper. Monitor the pump's operation closely during the initial stages to ensure that everything is working smoothly. Check for any abnormal noises, vibrations, or changes in pressure.

During the Pumping Operation

During the pumping operation, continuous monitoring and proper management are necessary.

1. Monitor the Hopper Level

Keep an eye on the hopper level to ensure a continuous supply of mortar. If the hopper runs out of mortar, air may enter the system, causing problems. Refill the hopper in a timely manner to maintain a steady flow of mortar.

2. Check the Pressure and Flow Rate

Regularly check the pressure gauge and flow meter to ensure that the pump is operating within the set parameters. If the pressure or flow rate deviates from the desired values, adjust the pump settings accordingly. This helps to ensure the quality of the mortar injection and prevent over - or under - pumping.

3. Inspect the Hoses and Connections

Periodically inspect the hoses and connections for any signs of leakage or damage. A leaking hose can not only waste mortar but also pose a safety hazard. If a leak is detected, stop the pump immediately and repair or replace the damaged hose or connection.

4. Maintain the Mixing Quality

If the pumping process takes a long time, the mortar in the hopper may start to settle or separate. Use a stirrer to keep the mortar well - mixed throughout the operation. This ensures that the mortar maintains its consistency and quality.

Stopping the Pump

When the mortar injection task is completed or needs to be paused, follow these steps to stop the pump safely.

1. Empty the Hopper

First, stop adding new mortar to the hopper. Let the pump continue to run until the hopper is empty and all the remaining mortar in the system is pumped out. This helps to prevent the mortar from hardening inside the pump and hoses.

2. Flush the System

After emptying the hopper, fill the hopper with clean water. Run the pump for a few minutes to flush out any remaining mortar from the pump, hoses, and other components. This is crucial to prevent the mortar from drying and clogging the system. Repeat the flushing process several times until the water coming out of the hoses is clear.

3. Turn Off the Power

Once the system is flushed, turn off the power supply to the pump. This ensures that the pump is completely shut down and reduces the risk of accidental startup.

Maintenance after Use

Proper maintenance after each use is essential to keep the mortar injection pump in good working condition.

1. Clean the Pump

Thoroughly clean all the components of the pump, including the hopper, valves, and pistons. Use a brush and water to remove any remaining mortar residue. Pay special attention to hard - to - reach areas where mortar may accumulate.

2. Store the Pump Properly

Store the pump in a dry and protected area. If possible, cover the pump to prevent dust and moisture from accumulating. This helps to prevent rust and corrosion, which can damage the pump over time.

3. Regular Maintenance Checks

Perform regular maintenance checks according to the manufacturer's recommendations. This may include changing the oil, inspecting the seals, and checking the wear and tear of the components. By following a regular maintenance schedule, you can extend the lifespan of your Mortar Injection Pump and ensure its reliable performance.

Different Types of Mortar Injection Pumps and Their Operating Features

In addition to the general operating procedures, different types of mortar injection pumps may have some unique features.

BW60-10 small grout pump pricehydraumatic grouting pump

1. Hydraumatic Grouting Pump

Hydraumatic grouting pumps use hydraulic power to drive the pumping process. They are known for their high - pressure capabilities, which make them suitable for deep - hole grouting and high - strength mortar injection. When operating a hydraumatic grouting pump, special attention should be paid to the hydraulic system. Regularly check the hydraulic fluid temperature and pressure to ensure optimal performance.

2. Small Grout Pump

Small grout pumps are more portable and suitable for small - scale projects or hard - to - reach areas. They are often electrically powered and have a relatively simple structure. However, due to their smaller size, they may have lower flow rates and pressures compared to larger pumps. When using a small grout pump, adjust the operation parameters carefully to meet the specific requirements of the project.

Conclusion

Operating a mortar injection pump requires careful attention to detail and strict adherence to the operating procedures. By following the pre - operation checks, proper starting and stopping steps, and regular maintenance, you can ensure the safe and efficient operation of the pump. Whether you are using a Mortar Injection Pump, a Hydraumatic Grouting Pump, or a Small Grout Pump, the key is to understand the specific features of the pump and operate it in accordance with the manufacturer's instructions.

If you are interested in purchasing a high - quality mortar injection pump or have any questions about their operation and maintenance, please feel free to contact us. We are here to provide you with professional advice and support to meet your construction needs.

References

  • Manufacturer's manuals of mortar injection pumps
  • Construction industry standards and guidelines related to mortar injection